Aurora Homepage
Forum Home Forum Home > The Vault > I'm New From Spectrum And I Need Help!
  Active Topics Active Topics
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

Forum LockedDesperate for Guidance!

 Post Reply Post Reply Page  12>
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
jswear View Drop Down
Newbie
Newbie


Joined: 18 Oct 2008
Online Status: Offline
Posts: 6
  Quote jswear Quote  Post ReplyReply Direct Link To This Post Topic: Desperate for Guidance!
    Posted: 24 Oct 2008 at 2:04am

Good day fellow decorators! 

 

I am new to computer controlled lighting and in desperate need of some help and/or advice.

 

I purchased the following equipment from D-Light in November of 2007:

 

Two ACx16 Platinum Plus Edition Controllers

One USB to RS-485 Adapter V2

Spectrum Software – Platinum Edition

 

After many unsuccessful hours in 2007 of trying to get the controllers to connect to my computer via the “Hardware Utility” I gave up and did my lighting installation without the system.  Of course I was bummed but I felt I could get the situation rectified before the 2008 holiday season.

 

So upon the recent notification from D-Light that they were no longer going to be selling and supporting Spectrum and now recommended the Aurora software I purchased the transition version.

 

I have downloaded the latest versions of the D-Light Hardware Utility, USB485 Driver and Firmware Updater.

 

But alas again after many hours of work I still cannot get the system up and running.

I am truly desperate for help.  Not wanting to be a completely uninformed newbie I have spent countless hours researching and reading posts on both the D-Light and Aurora forum pages and then applying what I have found.  But I am still having no luck.

 

Here is where I think I stand at this point in the process, bear with me as this part gets a little long but I wanted to be as specific as possible:

 

Installed D-Light Hardware Utility V2.0.16

Installed D-Light Firmware Updater V2.0.2

Installed USB485 Drivers V2.02.06

(I’m not sure if this was successful or not.  I know that it downloaded and was unzipped but I am not completely confident that it is actually in use by the COM Port.)

Installed Aurora Sequencer V1 Revision 1.3

 

I then connected one of the ACx16 controllers to my computer via a CAT5 cable, the USB to RS-485 Adapter and a fire wire cable.

I then plugged both power cords from the controller into a working power supply.

The red LED began flashing.

I then connected a working desk lamp switched to the ON position into the pigtail from the controller that is labeled “#1”.

I launched the “HWU”, set the “COM Port” to “5”, the correct port, and attempted to “Discover” the controller via the “Discover” tab.

I first tried this with the “Active Unit” set to “All” and the “Discover” range set to “01 to 0A”.

No luck, it could not find the controller.

I then switched the “Discover” range to “All” and tried again, but still no luck discovering the controller.

I then clicked on the “16CH Tests” tab and clicked “All On” and the desk lamp came on.

So I know that the computer and the controller are communicating in some form.

I then clicked on the “General Cfg” tab and set the “New Address” to “1”.

My understanding is that all of the ACx16 controllers ship with a #2 address so I wanted this controller to be #1 and my other controller to be #3.

 

I then connected the second controller in the exact same manner and got the exact same results.  Unable to discover the controller but able to turn the desk lamp on via the “All On” button.

So I set the address for this controller to “3”.

 

I launched Aurora, created a “New File” and selected an Audio file for the music.

I clicked on “Add New Network” within the “Serial Network Configuration.”

I set the “Network Number” to “NET 1” and the “Uses COM Port” to “COM 5”

I ran the “HWU” from the “Add-Ins” tab and was able to replicate my previously described process of turning the desk lamp on via the “All On” button, but this only worked with one controller and not the second that was now daisy chained to the first controller via a CAT5 cable.

 

I then began to set up “Channels” within the new Aurora file.

I right clicked in the appropriate area and clicked “Create New Channel.”

I set the “Device Name” to “1” and “Device Type” to “D-Light ACx16 (1.13+ firmware)”.

I set the “Network Segment” to “1”, “Device ID” to “1” and “Channel Number” to “1”.

I then set an “Event Marker” at the beginning and end of the “Spectogram display” to create one single event that runs from the beginning of the song to the end to be used just as test parameters.

I then placed a “Waveform” within this “Event Marker” next to “Channel 1” and Aurora created it.

I clicked the “White Light Bulb” within in the “Playback” controls so that its background turned red.

Then I hit play and the desk lamp never flickered, turned on or anything throughout the playback of the entire song..

The red LED on the ACx16 Controllers continued flashing and never remained lit.

 

I feel like I am so close to having everything operational but just can’t seem to get there.

I know that the gear from D-Light is good equipment but it seems like if you miss one thing during the set-up and then during the integration with Aurora then the whole system will not function.

 

I would be so, so appreciative if any of the more successful and experienced decorators out there could give me any assistance.  My 2.5 year old son would also be grateful as he is patiently waiting to see our Halloween install come to life!  While trying to diagnose the set-up issues I have continued with my lighting installation and it is all ready to be connected and controlled.

 

Thank you for consideration!

 

Best regards,

 

John Caldwell



Edited by jswear - 24 Oct 2008 at 8:30am
Back to Top
Bubba View Drop Down
DMX
DMX
Avatar

Joined: 27 Dec 2007
Location: Georgia
Online Status: Offline
Posts: 41
  Quote Bubba Quote  Post ReplyReply Direct Link To This Post Posted: 24 Oct 2008 at 6:09am

I assume you mean mini USB wire when you say Fire wire If I'm wrong please correct me. When you plug the controller in to a power source the LED should blink. Now plug in the cat 5 cable plugged into the adapter plugged into the mini USB that is plugged into the USB port on the computer. Open the Hardware utility and select the Com port, I use 4. Go to discover unit and select discover if you get nothing pick a diffrent Com port and try the discovery thing again unil it discovers your unit. If that doesn't work we need to try other things. This evening I can walk you through it on the phone if needed.

www.brightonbrittain.com
Back to Top
ChrisL1976 View Drop Down
Beta Testers
Beta Testers


Joined: 01 Sep 2008
Location: Kankakee, Ill
Online Status: Offline
Posts: 1341
  Quote ChrisL1976 Quote  Post ReplyReply Direct Link To This Post Posted: 24 Oct 2008 at 8:02am
We'll do what we can..BUT PLEASE in the mean time...edit your post and erase your email address and phone numbers....this is a public forum and thats only asking for trouble and 10,000 spam emails a day to your email

Edited by ChrisL1976 - 24 Oct 2008 at 8:03am
Chris

www.lightsonsixth.com
Back to Top
ChrisL1976 View Drop Down
Beta Testers
Beta Testers


Joined: 01 Sep 2008
Location: Kankakee, Ill
Online Status: Offline
Posts: 1341
  Quote ChrisL1976 Quote  Post ReplyReply Direct Link To This Post Posted: 24 Oct 2008 at 8:26am
1. Go into device manager on your computer and your should see one with PORTS  click on that, you should see the usb adapter listed.  Is it there?

2.  When you picked com5 in HWU.....the blinking light goes solid correct?

3.  stupid question, dont kill me....are you clicking the DISCOVER button in the open discover tab?  Next to the 01 pull down menu, upper left corner of the white box?    We have to get you finding these controllers in HWU.  If HWU cant truely discover your controller, then its probably not changing the device number.   I can run through HWU device number change sequence without having a controller hooked up. 

4.   Make a test sequence in Aurora, but set the device ID to 2....make a channel or two and put from light commands in the sequence and see what happens when you test it out.   Make sure your clicking the light bulb next to the in Aurora.  The blinking red light should go solid when you do this....or atleast when you click play.      Are the lights flashing to the commands you put in the sequence?




Edited by ChrisL1976 - 24 Oct 2008 at 8:29am
Chris

www.lightsonsixth.com
Back to Top
jswear View Drop Down
Newbie
Newbie


Joined: 18 Oct 2008
Online Status: Offline
Posts: 6
  Quote jswear Quote  Post ReplyReply Direct Link To This Post Posted: 24 Oct 2008 at 8:36am
Thanks Bubba.
Tried as you suggested but still did not discover the controller.
I tried to discover on all COM Ports listed and it did not find anything.
 
Best,
JC
Back to Top
jswear View Drop Down
Newbie
Newbie


Joined: 18 Oct 2008
Online Status: Offline
Posts: 6
  Quote jswear Quote  Post ReplyReply Direct Link To This Post Posted: 24 Oct 2008 at 9:19am
Hi Chris,
 
Thanks for the advice and I have modified accordingly.
 
1. Within Device Manager under Ports the following three things are listed:
Communication Port (COM1)
ECP Printer Port (LPT1)
USB Serial Port (COM5)
So I am assuming that COM5 is the adapter.
 
2. You are correct sir.
 
3.No stupid questions to me at this point! Yes, I am clicking the Discover button within the Discover tab.
 
4. Made a test sequence, built two channels, changed the Device ID to 2, connected some lights, clicked the Light Bulb and hit Play and it worked! Yes, when I clicked the Light Bulb and hit Play the LED went solid.
 
So have we learned that the controller has 2 as an address?
 
Best,
JC
Back to Top
LightsOnLogan View Drop Down
Admin Group
Admin Group


Joined: 11 Oct 2007
Online Status: Offline
Posts: 3187
  Quote LightsOnLogan Quote  Post ReplyReply Direct Link To This Post Posted: 24 Oct 2008 at 9:33am

I recommend working with D-Light to resolve the hardware issue.  It seems that your controller is still on the default ID of 2 and you are unable to get the hardware utility to properly talk to the controller in order to change it.

Back to Top
JonB256 View Drop Down
DMX
DMX
Avatar

Joined: 19 Dec 2007
Location: Granbury, TX
Online Status: Offline
Posts: 130
  Quote JonB256 Quote  Post ReplyReply Direct Link To This Post Posted: 24 Oct 2008 at 12:27pm

Sometimes I'm a "scorched earth" person with hardware, but I'd suggest reflashing the firmware on the controllers. The newest revision is better than what you have, anyway, since you got them back in 2007. 

I'm sure COM5 is correct for you. Using the Firmware Updater and connecting a single board, change the Port to COM5, then select Unit ID #2. Click Connect. If it can't connect, it will time out. Try other ID numbers you may or may not have changed. Failing there, try using the "Force" choice for ID.

JonB - D-Light user
Back to Top
Bubba View Drop Down
DMX
DMX
Avatar

Joined: 27 Dec 2007
Location: Georgia
Online Status: Offline
Posts: 41
  Quote Bubba Quote  Post ReplyReply Direct Link To This Post Posted: 24 Oct 2008 at 1:22pm
It seems I forget some of the basics as well. I forgot to add the fact that you need to click connect before doing the discovery. Select a COM port click connect then try to discover. Try that then get back with me.
www.brightonbrittain.com
Back to Top
ChrisL1976 View Drop Down
Beta Testers
Beta Testers


Joined: 01 Sep 2008
Location: Kankakee, Ill
Online Status: Offline
Posts: 1341
  Quote ChrisL1976 Quote  Post ReplyReply Direct Link To This Post Posted: 24 Oct 2008 at 1:45pm
Originally posted by LightsOnLogan

I recommend working with D-Light to resolve the hardware issue.  It seems that your controller is still on the default ID of 2 and you are unable to get the hardware utility to properly talk to the controller in order to change it.



I agree.......Its time to shoot this one over to Darryl and let him handle whats to be done.  Its sounds like a hardware issue if you can get output but now change the channel.  Although having it on 2 boards does sound weird.
Chris

www.lightsonsixth.com
Back to Top
 Post Reply Post Reply Page  12>

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.06
Copyright ©2001-2007 Web Wiz

This page was generated in 0.454 seconds.