Aurora Homepage
Forum Home Forum Home > Aurora Sequencer Software > Tips 'n' Tricks
  Active Topics Active Topics
  FAQ FAQ  Forum Search   Calendar   Register Register  Login Login

light intensity

 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
garagemahall4 View Drop Down
Newbie
Newbie


Joined: 12 Nov 2008
Online Status: Offline
Posts: 14
  Quote garagemahall4 Quote  Post ReplyReply Direct Link To This Post Topic: light intensity
    Posted: 30 Nov 2009 at 8:14am
I finally have my lights up and going after 2 years of having this program, the problem that I am having is that the lights are not as bright as they should be. How do I turn up the intensity on the lights? A  step by step would be great, if possible. Also, if I upgrade to the 1.04[ I am running 1.0 right now], will I lose my sequences that I have created already? Many thanks in advance, John.
Back to Top
Pony_God View Drop Down
Senior Member
Senior Member
Avatar

Joined: 01 Sep 2008
Location: Naples, FL
Online Status: Offline
Posts: 551
  Quote Pony_God Quote  Post ReplyReply Direct Link To This Post Posted: 30 Nov 2009 at 8:17am
The max burn setting is within D-Light's Harware Utility. I don't have it installed here, but I think it's on the general tab.
Fine. You're so smart you rig up the lights.
D-Light users Unite!
Back to Top
deweycooter View Drop Down
Development
Development


Joined: 14 Oct 2007
Location: League City, TX
Online Status: Offline
Posts: 674
  Quote deweycooter Quote  Post ReplyReply Direct Link To This Post Posted: 30 Nov 2009 at 8:26am
By default the Intensity event should be 100%.  To adjust it, right-click on the Intensity tool and adjust the slider accordingly. 

100% should be the same as plugging in your lights directly to the wall - confirm that these intensities are different first.  Then confirm that the intensities are set to 100% in your sequence. 

Last, it could be your hardware - use your hardware utility (do you have D-Light or LOR?) and turn the lights on.  If they don't come full on then (compared to a direct line to the wall), I would say you have an issue with your board.

I don't believe that any file formats have changed since 1.0 - meaning that you should be able to go to to 1.0.41.  Wait for someone else to chime in, but I'm pretty sure you'll be ok.

As always - take the time now to make a backup of your sequences and audio.  :)
Back to Top
garagemahall4 View Drop Down
Newbie
Newbie


Joined: 12 Nov 2008
Online Status: Offline
Posts: 14
  Quote garagemahall4 Quote  Post ReplyReply Direct Link To This Post Posted: 30 Nov 2009 at 8:54am
sorry, should have added that I use D-lite. thanks so far.
Back to Top
ChrisL1976 View Drop Down
Beta Testers
Beta Testers


Joined: 01 Sep 2008
Location: Kankakee, Ill
Online Status: Offline
Posts: 1341
  Quote ChrisL1976 Quote  Post ReplyReply Direct Link To This Post Posted: 30 Nov 2009 at 1:28pm
Originally posted by deweycooter



I don't believe that any file formats have changed since 1.0 - meaning that you should be able to go to to 1.0.41.  Wait for someone else to chime in, but I'm pretty sure you'll be ok.

As always - take the time now to make a backup of your sequences and audio.  :)


I do believe the upgrade to 1.0.32 last season required.....or was recommended that you open the file in 1.0.32 and save it.    I would save them in the upgraded version just to be safe.  Keep a backup copy of your current version sequences some place else.  

Edited by ChrisL1976 - 30 Nov 2009 at 1:29pm
Chris

www.lightsonsixth.com
Back to Top
garagemahall4 View Drop Down
Newbie
Newbie


Joined: 12 Nov 2008
Online Status: Offline
Posts: 14
  Quote garagemahall4 Quote  Post ReplyReply Direct Link To This Post Posted: 30 Nov 2009 at 7:52pm
Ok, the intensity is on 100%, the waveform was at miderange, so I turned it up, but it didnt change even after I saved it. So how do I go to the untility hardward for d-lite the check the setting there, again a step by step would be great. I did have a problem with 4 channels, but the forum told me that I didnt have enough lights on those channels, wow what a surprise that was. All the channels work perfect, just need the display to be 100% brightness, thanks in advance again, John
Back to Top
deweycooter View Drop Down
Development
Development


Joined: 14 Oct 2007
Location: League City, TX
Online Status: Offline
Posts: 674
  Quote deweycooter Quote  Post ReplyReply Direct Link To This Post Posted: 30 Nov 2009 at 8:26pm
D-Light HW Utility - you need to register first

1. connect your adapter
2. start the utility
3. select the com port
4. click ON - all channels should come on

This utility can be used to test lights, discover address numbers and set addresses.
Back to Top
garagemahall4 View Drop Down
Newbie
Newbie


Joined: 12 Nov 2008
Online Status: Offline
Posts: 14
  Quote garagemahall4 Quote  Post ReplyReply Direct Link To This Post Posted: 30 Nov 2009 at 8:27pm
Ok, got the intensity turned up, found it in the d-lite utility hardware, the wave form to event isn't that great but now its working, thanks for all your help, next year 32 channels with leds and stobes. Happy Holidays, John
Back to Top
 Post Reply Post Reply

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.06
Copyright ©2001-2007 Web Wiz

This page was generated in 0.329 seconds.